- 您现在的位置：买卖IC网 > Sheet目录840 > B32669B6105K (EPCOS Inc)FILM CAP 1.0000UF 10% 400VAC
B32669
AC applications (wound)
1.3
General notes on soldering
Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-
gory temperature T max . Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable coun-
termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 ° C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 ° C
MKT 160 ° C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled af-
ter the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings ≤ 10 mm (B32560/B32561) the following mea-
sures are recommended:
pre-heating to not more than 110 ° C in the preheater phase
rapid cooling after soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 15
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
B32671L1222J000
CAP FILM 2200PF 1.6KVDC RADIAL
B32678G3606K
CAP FILM 60UF 300VDC RADIAL
B32686A2104J
FILM CAP 0.1000UF 5% 2000V
B32686S2473K563
FILM CAP 0.0470UF 10% 2000V MFP
B32778G0406K
CAP FILM 40UF 1.1KVDC RADIAL
B32798G8306K
CAP FILM 30UF 875VDC RADIAL
B32916A3685K
CAP FILM 6.8UF 760VDC RADIAL
B32924B2155K
CAP FILM 1.5UF 310VAC RADIAL
相关代理商/技术参数
B32669B6155J
功能描述:薄膜电容器 1.5uF 400volts 5% Axial RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32669B6155K
功能描述:薄膜电容器 1.5uF 400volt 10% Axial RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32669B6205K
功能描述:薄膜电容器 2.0uF 400volts 10% Axial RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32669B6255K
功能描述:薄膜电容器 2.5uF 400volt 10% Axial RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32669B6305J
功能描述:薄膜电容器 3.0uF 400volts 5% Axial RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32669B6305K
功能描述:薄膜电容器 3.0uF 400volts 10% Axial RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32669B6405J
功能描述:薄膜电容器 4.0F 400volts 5% Axial RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32669B6405K
功能描述:薄膜电容器 4.0uF 400volts 10% Axial RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm